Expert Answers about GMC First Aid Kit
- Recommended Air Bag Kit for a 1987 Toyota Land Cruiser
- I do have an airbag suspension enhancement setup for your 1987 Toyota Land Cruiser's rear axle but I would strongly recommend replacing both front and rear leaf springs first. The leaf springs are a critical part of your vehicle's suspension and without them working properly you run the risk of further damage to other suspension components. Our suspension enhancement kits are designed to aid the factory suspension not substitute or replace components.
The only airbag kit we have for your...
view full answer... - Where To Find Bearing, Grease Seal, & Race Information For Replacement Parts
- The bearing, race, and grease seal information can be easily be found by removing any wheel from your trailer and taking down the part numbers from the inner and outer bearings to determine the correct replacement parts for your spindles.
I've shown this in the attached image so you can get a better visualization.
From here you should be able to find the corresponding replacement parts needed. Additionally, to get your lug and bolt pattern information you are going to want to measure...
view full answer... - Replacement Bearings, Races and Grease Seal For a 1-3/8" Straight Spindle
- We will have all the replacement bearing parts you will need as we do not have a bearing kit with all the parts you need. First we have the Bearing # L68149 and its corresponding Race # L68111. It is likely that your spindle will use the Grease Seal # 58846 but you should verify your measurements (ID 1.719" / OD 2.565") with your current seal. We also have the Tang Washer # 5-101 for a 1" diameter spindle nut.
The Seal Puller # PTW1219 and 7-Piece Installation Set # PTW83020 will aid in...
view full answer... - Can Air Lift Air Bag Kit for 2017 Nissan Titan be Used with Weight Distribution
- The Air Lift LoadLifter part # AL57331 that you referenced is a fit for your 2017 Nissan Titan 4WD crew cab and will offer you additional support when towing the travel trailer you mentioned. It can be used with an Equal-i-zer as well but you'll need to first decide how much air pressure you are going to use and then set up the Equal-i-zer again as you'll need less spring bar tension.
view full answer... - Parts Needed to Install Tekonsha Prodigy P3 Brake Controller on 2002 Nissan Xterra
- We have everything you need to install the excellent Tekonsha Prodigy P3 Trailer Brake Controller # 90195 in your 2002 Nissan Xterra, however there is not a wiring adapter currently available for this vehicle.
In order to install the controller, you will just need a couple of items. First, if your Xterra does not already have a 4-way connector installed, you will need to install the Tekonsha Upgraded Circuit Protected Tail Light Converter Hardwire Kit # 119178KIT. This is a universal hardwire...
view full answer... - Are Computer Aided Design (CAD) Files Available for Timbren Trailer Axle-less Kit A20RS545
- Timbren does not publish CAD drawings for their suspension products like # A20RS545 but I do have a dimensional drawing that I have linked for you. This covers key dimensions and mounting hole spacing. If you visit the product page for this item and scroll down you'll find other helpful diagrams that will aid your installation.
Timbren's Axle-Less suspension units should be installed directly across from one another. Before mounting the units, measure back from the coupler and mark the...
view full answer... - Can Gorilla-Lift Tailgate Lift Assist be Used on Folding Trailer Ramp
- The Gorilla-Lift Tailgate Lift Assist # GL1 could be used on a folding ramp. Yes, it should be attached to the first section of the ramp that is connected to the trailer. You could either fold the ramp and then lift or if your ramp allows you can use the lift assist to raise the entire ramp before folding.
view full answer... - Tonneau Cover And Ladder Rack Compatibility On A 2017 Toyota Tundra
- I do have a way for you to haul elongated items on your 2017 Toyota Tundra with a tonneau cover installed, however, as the mounting location of most tonneau covers are in the same spot as the mounting location for most ladder rack systems, the two are rarely compatible with one another.
The best option in order to haul additional or elongated cargo on your vehicle with a tonneau cover installed is a roof rack such as the Rhino-Rack Vortex Aero Crossbar System part # RRVA150B-2, part #...
view full answer... - 7-Way Trailer Wiring Connector Recommendation for a 2015 Nissan Rogue
- For your 2015 Nissan Rogue you will first need to start with a 4-way to be able to install a 7-way. For that you would need the part # 118480.
Now if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way.
If you do have trailer brakes you would need the # ETBC7 instead of the # 37185 and a brake controller. This kit comes with everything needed to wire up the 7-way and install a brake controller.
For a brake controller...
view full answer... - Do I Need To Remove the Harness From Vehicle When Storing the Tekonsha P-3 Trailer Brake Controller
- You can just unplug the wiring harness from the Tekonsha P-3 Trailer Brake Controller, item # 90195, when storing the unit. Be sure that when the wire is disconnected that the wire is not hanging in the way of any moving parts, such as the gas or brake pedal, and that it will not interfere with the operation of any of the vehicles necessary controls.
The instructions state to connect the harness into the unit first and then the truck so that you will see exactly how the connector latches....
view full answer... - How Wiring Is Run When Building New Trailer
- I have attached a link to our helpful article about wiring you can check out.
The article has written and visual aids that will help you run the wiring on the trailer. If you let me know how big the trailer is, I will be glad to make some recommendations that will work for you.
view full answer... - Snow Chains for 2018 Rav4
- Snow Chains are sold based on the tire size on the vehicle. The 2018 Rav4 were sold with two tire options; the 235/55-R18 (SE, Limited, Platinum, or Adventure) or the 225/65-R17 (LE, XLE) If you have a different size tire let me know and I will adjust the recommendation.
For the 235/55-R18, or the 225/65-R17, I recommend the Pewag # PWSXV580 snow chains. They are so close in size that they use the same chain. This chain is easy to install, has a diamond chain pattern that works very...
view full answer... - Hitch, Brake Controller & 7-Way for 2016 Freightliner Sprinter 2500
- For the 144-inch-wheelbase 2016 Freightliner Sprinter 2500 with step bumper we offer the 2-inch Class III Curt hitch # 13358. This installs without drilling and it includes all required mounting hardware. Note this hitch will NOT fit frames that are 30-3/8-inches wide measured outside to outside.
For a trailer brake controller I suggest the user-friendly Prodigy P2 # 90885 along with our 7-way installation kit # ETBC7. You will also need to first install a 4-pole harness # C59496. These...
view full answer... - Fifth Wheel and Suspension Enhancement Recommendation for a 2014 Ram 1500
- First let's start with a fifth wheel rail kit to allow a fifth wheel hitch to be installed in the bed of your 2014 Ram 1500 short bed. For a rail kit you would want a custom install kit like the part # C16306-204 that has been confirmed to fit your vehicle. This will cut install time in half when compared to a universal kit and will minimize drilling.
Since the # TDR1500DQ installs by attaching to the jounce bumper mount of your frame it would be compatible with this rail kit.
For a...
view full answer... - Recommended Trailer Brake Controller and Wiring for 2014 Mercedes-Benz GL450
- We have everything you need to install a trailer brake controller on your 2014 Mercedes-Benz GL450, however there is not a plug-in adapter available that will fit this vehicle. The Tekonsha # 3035-P that you referenced is designed for certain model Ford, Lincoln and Mercury vehicles. It is not compatible with your GL450.
If your Mercedes GL450 does not have the factory tow package, you will first need to install a 4-Way connector with the Curt Upgraded Circuit Protected Tail Light w Converter...
view full answer... - How To Install The Air Lift AirLift 1000 Air Helper Springs On A 2004 Honda Odyssey
- I can certainly walk you through the instructions for installing the Air Lift AirLift 1000 Air Helper Springs for Coil Springs part # AL60740 on the rear of your 2004 Honda Odyssey, however, we have not had a chance to install these springs on a Honda Odyssey yet.
In order to install these air springs on your vehicle, you will first want to remove the factory rear jounce spring. In order to do this you must first Jack up the rear of the vehicle. Put safety stands under the frame so wheels...
view full answer... - 4-Bike Rack That Has Arm Hooks that Fold Down and Out of the Way
- We have 4 bike platform racks that have wheel arms that work in a unique way. When you are loading the first bike, the arms of the other three positions lay flat and completely out of the way. The wheel arm for the bike you are loading moves away from the bike for you to get it into position. Check out the video of the Saris MHS Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount # SAR95MR and see if this will work better for you.
view full answer... - Bearing Kit For Lippert 5,200LB Axle Tag Number 121067
- Your 5,200LB Lippert axle 121067 will use the Bearing Kit # BK3-300. This will give you the bearings, races, grease seal, and cotter pin for one axle hub.
The Seal Puller # PTW1219 and Installation Set # PTW83020 will aid you in the removal and installation of the parts. I recommend using the LubriMatic LMX Industrial Strength Grease # L11390 with your bearings as it works great in both hot and cold climates.
view full answer... - Recommended Trailer Wiring Harness for 2008 VW City Golf
- To install a 4-Way connector on your 2008 VW City Golf, I recommend the Tekonsha Hardwire Kit # 119178KIT. This harness does include the needed circuit protected tail light converter that will adapt the 3-Wire system on your vehicle to the standard trailer tail light 2-Wire system. This kit also includes a circuit tester that will aid in locating the correct wires to connect to on your City Golf.
I have attached the written installation instructions that you can take a look at.
view full answer... - Replacement Soft Top Recommendation for a 1987 Suzuki Samurai
- We don't carry the replacement hardware for the soft top of your 1987 Suzuki Samurai, but the Bestop Replace-A-Top # B5136101 comes with everything needed to replace the top of your vehicle and attach to factory hardware.
view full answer...
Go To Results